| |
Please view our
list of frequently asked
questions that may assist
your particular needs.
If you still need assistance,
please contact
us.
General FAQs | Rumble
Road FAQs | CrankCase FAQs | Raw200 FAQs
• What types of audio devices can I hook up to CrankCase?
• Can I use any personal stereo with CrankCase?
• Can CrankCase be used with a conventional AM/FM car stereo
or amplifier?
• Will CrankCase work only with Rumble Road speakers?
• How big is CrankCase? How much does it weigh?
• Where can I install CrankCase? Can I install it on my bike's
handlebars without drilling holes?
• Can I connect CrankCase directly to the battery?
• Will CrankCase work with two sets of speakers?
• Is CrankCase waterproof?
• Is CrankCase prepackaged with mounting hardware, or do
I have to order hardware separately?
What types of audio devices can I hook up to CrankCase?
Easily installed on handlebars or other spots within easy, safe reach, CrankCase™ works
with virtually any portable stereo radio, or MP3, CD or cassette player featuring
a standard 3.5mm mini-plug headphone jack. For the relatively few devices manufactured
with the newer 2.5mm stereo jacks, adapters are available from electronics stores.
CrankCase™ also works with many conventional car stereo or amplifier setups
on bikes, ATVs and other powersports vehicles when the devices have standard
line-level outputs. In addition, the output amplifier designed into
CrankCase can drive standard portable headphones. In fact, if wired properly,
CrankCase enables you to control volume on your in-helmet headphones,
as well.
Return
to Top
Can I use any personal stereo with CrankCase?
You can use CrankCase™ with virtually any personal radio, or CD, cassette
or MP3 player equipped with a standard 3.5mm mini-plug headphone jack. As noted
above, for the relatively few devices manufactured with the newer 2.5mm stereo
jacks, adapters are available from electronics stores. Products with "floating
ground" amplifiers, such as very low-end FM radios, may not work optimally
with MHI audio components.
Return
to Top
Can CrankCase be used with a conventional AM/FM car stereo or amplifier?
Yes, CrankCase™ works with any car stereo or amplifier equipped with line-level inputs or outputs.
Return
to Top
Will CrankCase work only with Rumble Road speakers?
No, CrankCase™ features line-level inputs and outputs to enable the device to work with most any amplifier or amplified speaker assembly – not just product manufactured by MHI.
Return
to Top
How big is CrankCase? How much does it weigh?
The small-footprint billet aluminum case measures approximately 1.7" wide
by 1.8" high and is 1.3" deep without the knob and mounting hardware,
which altogether increase depth of the unit to 3.4". CrankCase™ weighs
6.3 ounces, including built-in connection wires.
Return
to Top
Where can I install CrankCase? Can I install it on my bike's handlebars without drilling holes?
Easily installed on 1" handlebars or other spots within easy, safe reach,
CrankCase™ is compact enough to fit just about anywhere. The device measures
approximately 1.7" wide by 1.8" high and is 1.3" deep without
the mounting hardware (3.4" width). Handlebar mounting without drilling
holes in the bar is possible using the custom two-piece hardware included with
each CrankCase. Standard 10-32 mounting holes are machined into the back of
each unit for ease in mounting using the exclusive bracket and backstrap packaged
with each CrankCase™.
Return
to Top
Can I connect CrankCase directly to the battery?
CrankCase™ is switched, fused (5 amps) and ready to wire either directly
to a 12-volt battery or to another 12-volt source on your bike, such as an
existing accessory line or headlight power line. CrankCase™ includes
a switched and fused power line output wire, which allows you to then use CrankCase™ to
control your bike’s other electronic devices – such as an amplifier
or powered speakers (available from MHI). The output amplifier also is designed
to drive standard portable headphones. If you need assistance, your local automotive
sound shop or motorcycle dealer should be able to help you find a suitable
power source, as well as properly install the system.
Return
to Top
Will CrankCase work with two sets of speakers?
Yes! Some of our customers have cleverly installed "quad" mounts –
one pair of Rumble Road™ speakers on the handlebars and an opposing pair
astride the passenger seat. If you still can’t quite picture it, this
approach is beautifully illustrated by one of our customer testimonial montages.
Each pair of Rumble Road™ Premium speakers draws about 5 amps peak from
the battery. You will need to install one CrankCase™ per each pair of
speakers that you want to both power and drive.
Return
to Top
Is CrankCase waterproof?
CrankCase™ is water-resistant, meaning that it can tolerate
splashed water, but it is not literally waterproof and cannot tolerate submersion.
For enhanced protection from the elements, the unit’s case and backplate
are precision-machined billet aluminum for an exceptionally tight fit. The
backplate is secured by screws at six points. If you do suspect water damage,
allow the unit to dry out over a day or two and re-power the system.
Return
to Top
Is CrankCase prepackaged with mounting hardware, or do I have to order hardware separately?
For your convenience, each CrankCase™ includes a custom mounting bracket
and backstrap ready to install on 1" handlebars. The removable two-piece
clamp makes it easy to mount CrankCase™ on handlebars other than standard
1" if you choose to use your own hardware.
Return
to Top
|
|
